Mini Samples ELISA Kit for Fibrinopeptide A (FPA)
- Product No.MEB237Ra
- Organism SpeciesRattus norvegicus (Rat) Same name, Different species.
- Sample TypeSerum, plasma, tissue homogenates, cell lysates, cell culture supernates and other biological fluids
- Test MethodCompetitive Inhibition
- Assay Length3h
- Detection Range370.4-30,000pg/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 129.1pg/mL.
- DownloadInstruction Manual
- UOM 48T96T 96T*5 96T*10 96T*100
For more details, please contact local distributors! US$ 912
For more details, please contact local distributors! US$ 4104
For more details, please contact local distributors! US$ 7752
For more details, please contact local distributors! US$ 63840
For more details, please contact local distributors!
This assay has high sensitivity and excellent specificity for detection of Mini Samples Fibrinopeptide A (FPA).
No significant cross-reactivity or interference between Mini Samples Fibrinopeptide A (FPA) and analogues was observed.
Matrices listed below were spiked with certain level of recombinant Mini Samples Fibrinopeptide A (FPA) and the recovery rates were calculated by comparing the measured value to the expected amount of Mini Samples Fibrinopeptide A (FPA) in samples.
|Matrix||Recovery range (%)||Average(%)|
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Mini Samples Fibrinopeptide A (FPA) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Mini Samples Fibrinopeptide A (FPA) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Mini Samples Fibrinopeptide A (FPA) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Reagents and materials provided
|Pre-coated, ready to use 96-well strip plate||1||Plate sealer for 96 wells||4|
|Detection Reagent A||1×60µL||Assay Diluent A||1×6mL|
|Detection Reagent B||1×60µL||Assay Diluent B||1×6mL|
|TMB Substrate||1×9mL||Stop Solution||1×3mL|
|Wash Buffer (30 × concentrate)||1×10mL||Instruction manual||1|
Assay procedure summary
1. Prepare all reagents, samples and standards;
2. Add 25µL standard or sample to each well.
And then add 25μL prepared Detection Reagent A immediately.
Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 50µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 50µL Substrate Solution. Incubate 10-20 minutes at 37°C;
7. Add 25µL Stop Solution. Read at 450 nm immediately.
|Catalog No.||Related products for research use of Rattus norvegicus (Rat) Organism species||Applications (RESEARCH USE ONLY!)|
|CPB237Ra21||OVA Conjugated Fibrinopeptide A (FPA)||Immunogen; SDS-PAGE; WB.|
|MEB237Ra||Mini Samples ELISA Kit for Fibrinopeptide A (FPA)||Enzyme-linked immunosorbent assay for Antigen Detection.|
|CEB237Ra||ELISA Kit for Fibrinopeptide A (FPA)||Enzyme-linked immunosorbent assay for Antigen Detection.|
|KSB237Ra11||ELISA Kit DIY Materials for Fibrinopeptide A (FPA)||Main materials for "Do It (ELISA Kit) Yourself".|