ELISA Kit for Myoglobin (MYO)
- Product No.SEA480Mu
- Organism SpeciesMus musculus (Mouse) Same name, Different species.
- Sample Typeserum, plasma, tissue homogenates and other biological fluids
- Test MethodDouble-antibody Sandwich
- Assay Length3h
- Detection Range31.2-2,000pg/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 12.4pg/mL.
- DownloadInstruction Manual
96T*5 96T*10 96T*100
For more details, please contact local distributors! US$ 648
For more details, please contact local distributors! US$ 2916
For more details, please contact local distributors! US$ 5508
For more details, please contact local distributors! US$ 45360
For more details, please contact local distributors!
This assay has high sensitivity and excellent specificity for detection of Myoglobin (MYO).
No significant cross-reactivity or interference between Myoglobin (MYO) and analogues was observed.
Matrices listed below were spiked with certain level of recombinant Myoglobin (MYO) and the recovery rates were calculated by comparing the measured value to the expected amount of Myoglobin (MYO) in samples.
|Matrix||Recovery range (%)||Average(%)|
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Myoglobin (MYO) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Myoglobin (MYO) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Myoglobin (MYO) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Reagents and materials provided
|Pre-coated, ready to use 96-well strip plate||1||Plate sealer for 96 wells||4|
|Detection Reagent A||1×120µL||Assay Diluent A||1×12mL|
|Detection Reagent B||1×120µL||Assay Diluent B||1×12mL|
|TMB Substrate||1×9mL||Stop Solution||1×6mL|
|Wash Buffer (30 × concentrate)||1×20mL||Instruction manual||1|
Assay procedure summary
1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.
|European Journal of Applied Physiology||Acute leukocyte, cytokine and adipocytokine responses to maximal and hypertrophic resistance exercise bouts Pubmed:25145982|
|Catalog No.||Related products for research use of Mus musculus (Mouse) Organism species||Applications (RESEARCH USE ONLY!)|
|RPA480Mu02||Recombinant Myoglobin (MYO)||Positive Control; Immunogen; SDS-PAGE; WB.|
|RPA480Mu01||Recombinant Myoglobin (MYO)||Positive Control; Immunogen; SDS-PAGE; WB.|
|PAA480Mu02||Polyclonal Antibody to Myoglobin (MYO)||WB; IHC; ICC; IP.|
|PAA480Mu01||Polyclonal Antibody to Myoglobin (MYO)||WB; IHC; ICC; IP.|
|LAA480Mu81||FITC-Linked Polyclonal Antibody to Myoglobin (MYO)||WB; IHC; ICC; IF.|
|LAA480Mu71||Biotin-Linked Polyclonal Antibody to Myoglobin (MYO)||WB; IHC; ICC.|
|SEA480Mu||ELISA Kit for Myoglobin (MYO)||Enzyme-linked immunosorbent assay for Antigen Detection.|
|SCA480Mu||CLIA Kit for Myoglobin (MYO)||Chemiluminescent immunoassay for Antigen Detection.|