ELISA Kit for Erythropoietin Receptor (EPOR)



This assay has high sensitivity and excellent specificity for detection of Erythropoietin Receptor (EPOR).
No significant cross-reactivity or interference between Erythropoietin Receptor (EPOR) and analogues was observed.


Matrices listed below were spiked with certain level of recombinant Erythropoietin Receptor (EPOR) and the recovery rates were calculated by comparing the measured value to the expected amount of Erythropoietin Receptor (EPOR) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 87-94 90
EDTA plasma(n=5) 83-90 87
heparin plasma(n=5) 97-105 102


Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Erythropoietin Receptor (EPOR) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Erythropoietin Receptor (EPOR) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%


The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Erythropoietin Receptor (EPOR) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 88-99% 86-99% 80-95% 92-104%
EDTA plasma(n=5) 91-101% 99-105% 95-102% 91-99%
heparin plasma(n=5) 79-89% 97-105% 79-90% 81-92%


The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Reagents and materials provided

Reagents Quantity Reagents Quantity
Pre-coated, ready to use 96-well strip plate 1 Plate sealer for 96 wells 4
Standard 2 Standard Diluent 1×20mL
Detection Reagent A 1×120µL Assay Diluent A 1×12mL
Detection Reagent B 1×120µL Assay Diluent B 1×12mL
TMB Substrate 1×9mL Stop Solution 1×6mL
Wash Buffer (30 × concentrate) 1×20mL Instruction manual 1

Assay procedure summary

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.



Magazine Citations
J Appl Physiol (1985). Decreased plasma soluble erythropoietin receptor in high-altitude excessive erythrocytosis and Chronic Mountain Sickness Pubmed:25324511
J Appl Physiol Plasma soluble erythropoietin receptor is decreased during sleep in Andean highlanders with Chronic Mountain Sickness Pubmed:27125843
Catalog No. Related products for research use of Rattus norvegicus (Rat) Organism species Applications (RESEARCH USE ONLY!)
RPA027Ra01 Recombinant Erythropoietin Receptor (EPOR) Positive Control; Immunogen; SDS-PAGE; WB.
PAA027Ra01 Polyclonal Antibody to Erythropoietin Receptor (EPOR) WB; IHC; ICC; IP.
LAA027Ra71 Biotin-Linked Polyclonal Antibody to Erythropoietin Receptor (EPOR) WB; IHC; ICC.
MAA027Ra21 Monoclonal Antibody to Erythropoietin Receptor (EPOR) WB; IHC; ICC; IP.
SEA027Ra ELISA Kit for Erythropoietin Receptor (EPOR) Enzyme-linked immunosorbent assay for Antigen Detection.